Installation Of Heating Boiler Installation With His hands

In that case, if your private home is not connected to the centralized heating system, it can not do without everything his little boiler. The equipment, the heart of which is a pot (usually a gas), it is extremely expensive, and additionally afford layman has even masters and greed, which require the installation and debugging of the boiler, often too much money.

But an alternative treatment to the professionals there - installation of the boiler heating with his hands. The process is quite complicated and requires knowledge of at least an essential skill for construction works. Next, we elaborate on exactly how to make installation of the boiler equipment and what to pay particular attention.

Construction of a boiler room.

The preparation room precedes installation of a heating boiler with his hands. If the furnace runs on gas - and it is almost 100 per cent of cases - it can be installed no closer than one meter away from the stove and other gas equipment. Special demands are made to the very premise - it should be closed and have an area of at least 8 square meters If these conditions are not met, gas service will just refuse to put your boiler on the account and does not authorize the access to gas.

By itself, the installation of the heating boiler own hands is divided into four stages:

• - the installation of the boiler on the wall and arrangement of the chimney;
• - The boiler connection to the home heating system;
• - Connect the boiler to a gas pipeline.

Below is a detailed look at all these stages separately.

Installation of the boiler on the wall and arrangement of the chimney.

The simplest step for his little boiler equipment - boiler plant in its rightful place. For this purpose, the wall must rancher it horizontal level (line), which mark the point where the bracket will be attached. Then, the selected point of the hole is drilled, securely installed fastening elements, which are put up and the boiler itself. At the first stage - Installation - completed.

The next stage - equipping the chimney. In principle, this work is also simple - drill holes (breaks the wall or ceiling, depending on the boiler model) through which the street is displayed sleeve. However, you must take into account some points.Otherwise.there is a danger that the chimney will have to redo. First - outdoor pipe must be of a certain length (if it takes place in the wall, about 30 centimeters, if through the roof, then just above the top of the ceiling). The second - the angle of the street of the pipe should be done a little bit negative (10 degrees tilt enough), that is, the plug going into the ground. If this is neglected, it is possible instability in the operation of the boiler.

Connecting the boiler to the home heating system.

People who have experience in installation works can argue about what stage of the installation of the boiler with his hands the easiest. Some may say that the connection to your home heating system is incomparably easier. Indeed, if you are targeting freely among the many existing locking accessories, valves, and filters, the process will take about an hour of power.

Connection technology for input (ingress of water into the boiler) and the output (supply of hot water in the pipes) is slightly different. So, for the first case, first you need to put an American (extremely practical form of plug-in connection), then there is a coarse cleaning filter installation (it is also called "sump") completes the design shut-off valve, which goes into the pipe. The output is equipped with a much easier - starting with the same American, followed by a shut-off valve and pipe heating system. Setting the output and filter cartridges is useful. When you first launch the new heating cartridge is changed after fifteen minutes - the so-called test run. As an option, also be mounted in the expansion tank, which serves to receive excess water.

Connecting the boiler to the gas pipeline.

If you are installing the heating boiler with his hands, then with great care Treat stage boiler connection to the gas pipeline. The best option - to entrust to professionals from the gas service. So you zabrakovyvaniya from your boiler will save, and security will be assured for all hundred. All the more so for the installation of shut-off valve have to use a special pipe wrench, screw the junction carefully sealed and equipped with a tow in the pipeline filter. All work is carried out exclusively using captive nuts, but only a metal pipe can be used for entry of gas - no rubber hoses.

The installation of the boiler heating with their hands is completed. If all works are carried out correctly, there are no reliability problems will not arise.